MQTT

Dieses Gerät unterstützt MQTT 3.1.1 um konfigurierte Nachrichten zu verschicken, und auch Kommandos entgegenzunehmen. Dieses Kapitel ist für alle Gude Geräte allgemein gehalten, manche Gude Modelle haben keine schaltbaren Ports.

• Default Port für eine unverschlüsselte Verbindung ist Port 1883.
• Default Port für eine TLS gesicherte Verbindung ist Port 8883.
• Wenn der Broker einen anonymen Login erlaubt, sind Benutzername und Passwort beliebig, aber ein Benutzername muss angegeben werden.
• Wenn mehrere MQTT Clients mit einem Broker verbunden sind, müssen die Namen der Clients verschieden sein. Aus diesem Grund wird als Default Name "client_xxxx" generiert. Dabei sind "xxxx" die 4 letzten Stellen der MAC-Adresse.

Nachrichtenformat

Die MQTT Nachrichten des Gerätes werden immer im JSON Format verschickt. Z.B.

{"type": "portswitch", "idx": 2, "port": "2", "state": 1, "cause": {"id": 2, "txt": "http"}, "ts": 1632}

Dies ist ein Schalten des zweiten Ports in den Zustand ("state") on. Die Quelle des Schaltkommando ist CGI ("http"). Der Index ist immer numerisch, "port" kann bei Geräten mit mehreren Banks auch alphanumerisch sein, z.B. "A2". Am Ende folgt ein timestamp ("ts"), der die Anzahl der Sekunden anzeigt, die das Gerät eingeschaltet ist, oder im Unix Format in der lokalen Zeitzone, wenn das Gerät sich mit einem NTP-Server synchronisiert hat.

MQTT Topic Prefix

Das Topic Prefix für die Nachrichten ist in der MQTT Konfiguration einstellbar. Ein Default wäre z.B. "de/gudesystems/epc/[mac]". Hier steht "[mac]" als Platzhalter für die MAC-Adresse des Gerätes, ein weiterer möglicher Platzhalter ist "[host]", der den Host-Namen beinhaltet. Ein Beispiel Topic für eine Schaltnachricht des zweites Ports wäre dann:

"de/gudesystems/epc/00:19:32:01:16:41/switch/2".

Ausführen von Konsolen Kommandos

Das Gerät kann über MQTT komplett mit Konsolen Kommandos ferngesteuert werden. Eine Liste aller Kommandos findet sich im Kapitel Konsole . Je nach Topic werden die Kommandos in verschiedenen Formaten angenommen.

Als Default ist das Ausführen vom Kommandos nicht erlaubt, sondern muss in der MQTT Konfiguration ("Permit CLI commands") freigeschaltet werden!

Format 1: Kommando in JSON Syntax

Publish Topic: "de/gudesystems/epc/00:19:32:01:16:41/cmd"
Publish Message: "{"type": "cli", "cmd": "port 2 state set 1", "id": 10}"

Antwort vom Gerät an "de/gudesystems/epc/00:19:32:01:16:41/cmdres"
"{"type": "cli", "cmdres": ["OK."], "result": {"num": 0, "hint": "ok"}, "id": 10}"
Das JSON Objekt "result" gibt zurück, ob das Kommando valide war. Das Objekt "id" im Kommando ist optional und wird in der Antwort vom Gerät durchgereicht. Die Übergebene Nummer kann helfen eine Synchronizität zwischen Kommando und Antwort über den Broker herzustellen.

Format 2: Raw Text

Publish Topic: "de/gudesystems/epc/00:19:32:01:16:41/cmd/cli"
Publish Message: "port 2 state set 1"

Antwort vom Gerät an "de/gudesystems/epc/00:19:32:01:16:41/cmdres/cli"
"OK."

Format 3: Vereinfachtes Port schalten

Publish Topic: "de/gudesystems/epc/00:19:32:01:16:41/cmd/port/2"
Publish Message: "0" oder "1"
Antwort vom Gerät an "de/gudesystems/epc/00:19:32:01:16:41/cmdres/port/2"
"0" oder "1"
Diese Spezialform existiert nur für die Port Schaltbefehle.

Device Data Summary

In der Device Data Summary werden in einem JSON Objekt die wichtigsten Daten des Gerätes zusammengefasst und in einem konfigurierbaren Zeitintervall periodisch verschickt. Diese Zusammenfassung hängt von den Eigenschaftes des Gerätes und der angeschlossenen Sensoren ab, und könnte z.B. so aussehen:

Topic: de/gudesystems/epc/00:19:32:01:16:41/device/telemetry

Nachricht:

Befehlsliste

logout	go to login prompt when enabled
quit	quits telnet session - nothing in serial console
back	back one cmd level
help	show all cmds from this level
help all	show all cmds
clock	enters cmd group "clock"
clock ntp enabled set {OFF=0|ON=1}	enables ntp
clock ntp enabled show	shows if ntp enabled
clock timezone set {minutes}	sets timezone
clock timezone show	shows timezone
clock dst enabled set {OFF=0|ON=1}	enables dst
clock dst enabled show	shows if dst is enabled
clock manual set "{hh:mm:ss yyyy-mm-dd}"	sets time and date manually
clock show	shows actual time and date
clock ntp server {PRIMARY=0|BACKUP=1} set "{dns_name}"	sets ntp server name
clock ntp server {PRIMARY=0|BACKUP=1} show	shows ntp server name
console	enters cmd group "console"
console version	shows unique console version number
console telnet enabled set {OFF=0|ON=1}	enables telnet on/off
console telnet enabled show	shows if telnet enabled
console telnet port set {ip_port}	sets telnet port
console telnet port show	shows telnet port
console telnet raw set {OFF=0|ON=1}	sets raw mode (disables editing) on/off
console telnet raw show	shows if raw mode enabled
console telnet echo set {OFF=0|ON=1}	enables echo on/off
console telnet echo show	shows if echo enabled
console telnet activeneg set {OFF=0|ON=1}	enables telnet active negotiation (IAC) on/off
console telnet activeneg show	shows if active negotiation enabled
console telnet login set {OFF=0|ON=1}	enables login on/off
console telnet login show	shows if login enabled
console telnet login local set {OFF=0|ON=1}	enables local login on/off
console telnet login local show	shows if local login enabled
console telnet login radius set {OFF=0|ON=1}	enables login for RADIUS on/off
console telnet login radius show	shows if RADIUS login enabled
console telnet login delay set {OFF=0|ON=1}	enables delay (after 3 login fails) on/off
console telnet login delay show	shows if login delay enabled
console telnet pushmsgs config set {OFF=0|ON=1}	enables persistent push msgs
console telnet pushmsgs config show	shows if persistent push msgs are enabled
console telnet pushmsgs set {OFF=0|ON=1}	enables temporary push msgs
console telnet pushmsgs show	shows if temporary push msgs are enabled
console telnet user set "{username}"	sets login user name
console telnet user show	shows login user name
console telnet passwd set "{passwd}"	sets login password
console telnet passwd hash set "{passwd}"	sets login hashed password
console ssh enabled set {OFF=0|ON=1}	enables SSH
console ssh enabled show	shows if SSH enabled
console ssh port set {ip_port}	sets SSH port
console ssh port show	shows SSH port
console ssh echo set {OFF=0|ON=1}	enables echo on/off
console ssh echo show	shows if echo enabled
console ssh pushmsgs config set {OFF=0|ON=1}	enables persistent push msgs
console ssh pushmsgs config show	shows if persistent push msgs are enabled
console ssh pushmsgs set {OFF=0|ON=1}	enables temporary push msgs
console ssh pushmsgs show	shows if temporary push msgs are enabled
console ssh public hash set "{passwd}"	sets hash of SSH public key
console ssh public hash show	shows hash of SSH public key
console serial enabled set {OFF=0|ON=1}	enables serial console on/off
console serial enabled show	shows if serial console enabled
console serial raw set {OFF=0|ON=1}	sets raw mode (disables editing) on/off
console serial raw show	shows if raw mode enabled
console serial echo set {OFF=0|ON=1}	enables echo on/off
console serial echo show	shows if echo enabled
console serial kvm set {OFF=0|ON=1}	enables binary KVM cmds on serial port on/off
console serial kvm show	shows if binary KVM cmds enabled
console serial utf8 set {OFF=0|ON=1}	enables UTF8 support
console serial utf8 show	shows if UTF8 enabled
console serial login set {OFF=0|ON=1}	enables login on/off
console serial login show	shows if login enabled
console serial login local set {OFF=0|ON=1}	enables local login on/off
console serial login local show	shows if local login enabled
console serial login radius set {OFF=0|ON=1}	enables login for RADIUS on/off
console serial login radius show	shows if RADIUS login enabled
console serial login delay set {OFF=0|ON=1}	enables delay (after 3 login fails) on/off
console serial login delay show	shows if login delay enabled
console serial pushmsgs config set {OFF=0|ON=1}	enables persistent push msgs
console serial pushmsgs config show	shows if persistent push msgs are enabled
console serial pushmsgs set {OFF=0|ON=1}	enables temporary push msgs
console serial pushmsgs show	shows if temporary push msgs are enabled
console serial user set "{username}"	sets login user name
console serial user show	shows login user name
console serial passwd set "{passwd}"	sets login password
console serial passwd hash set "{passwd}"	sets login hashed password
email	enters cmd group "email"
email enabled set {OFF=0|ON=1}	enables email on/off
email enabled show	shows if email is enabled
email sender set "{email_addr}"	sets email sender address
email sender show	shows email sender address
email recipient set "{email_addr}"	sets email recipient address
email recipient show	shows email recipient address
email server set "{dns_name}"	sets email SMTP server address
email server show	shows email SMTP server address
email port set {ip_port}	sets email SMTP port
email port show	shows email SMTP port
email security set {NONE=0|STARTTLS=1|SSL=2}	sets SMTP connection security
email security show	shows SMTP connection security
email auth set {NONE=0|PLAIN=1|LOGIN=2}	sets email authentication
email auth show	show email authentication
email user set "{username}"	sets SMTP username
email user show	shows SMTP username
email passwd set "{passwd}"	sets SMTP password
email passwd hash set "{passwd}"	sets crypted SMTP password
email testmail	send test email
ethernet	enters cmd group "ethernet"
ethernet mac show	shows MAC address
ethernet link show	shows ethernet link state
ethernet phyprefer set {10MBIT_HD=0|10MBIT_FD=1|100MBIT_HD=2|100MBIT_FD=3}	sets preferred speed for PHY Auto Negotiation
ethernet phyprefer show	shows preferred speed for PHY Auto Negotiation
extinput	enters cmd group "extinput"
extinput {port_num} {inp_num} state show	shows input state
extinput all state {MODE0=0|MODE1=1|MODE2=2} show	shows input state of all ports in 3 different view modes
extinput {port_num} {inp_num} name set "{name}"	sets sensor name to label
extinput {port_num} {inp_num} name show	shows label of sensor
extinput {port_num} {inp_num} invert enabled set {OFF=0|ON=1}	inverts input on/off
extinput {port_num} {inp_num} invert enabled show	shows if input inverted
extinput {port_num} {inp_num} label {LOW=0|HIGH=1} set "{name}"	sets input low/high text
extinput {port_num} {inp_num} label {LOW=0|HIGH=1} show	shows input low/high text
extinput {port_num} {inp_num} events set {OFF=0|ON=1}	enables input events on/off
extinput {port_num} {inp_num} events show	shows if input events are enabled
extinput {port_num} {inp_num} events type set "{EVT_SYSLOG=0,EVT_SNMP=1,EVT_EMAIL=2 ,EVT_BEEPER=5,EVT_DISPLAY=6,EVT_CONS OLE=7,EVT_MQTT=8}"	enables different event types
extinput {port_num} {inp_num} events type show	shows what event types are enabled
extinput {port_num} {inp_num} publish mode set {NONE=0|INTERVAL=1|DELTA=2| INTERV_DELTA=3}	sets publish mode
extinput {port_num} {inp_num} publish mode show	showshows publish mode
extinput {port_num} {inp_num} publish mqtt retain set {OFF=0|ON=1}	sets mqtt retain
extinput {port_num} {inp_num} publish mqtt retain show	shows if mqtt retain set
extinput {port_num} {inp_num} publish timer set {num_secs}	sets publish time interval
extinput {port_num} {inp_num} publish timer show	shows publish time interval
extinput {port_num} {inp_num} {LOW=0|HIGH=1} port set {port_num}	sets Port for Power Port Switching actions
extinput {port_num} {inp_num} {LOW=0|HIGH=1} port show	shows Port for Power Port Switching actions
extinput {port_num} {inp_num} {LOW=0|HIGH=1 state set {OFF=0|ON=1|DISABLED=2}	sets Port state for Power Port Switching actions
extinput {port_num} {inp_num} {LOW=0|HIGH=1} state show	shows Port state for Power Port Switching actions
extsensor	enters cmd group "extsensor"
extsensor all show	shows all values from connected external sensors
extsensor all show	shows all plugged sensors and fields
extsensor {port_num} {sen_field} value show	shows sensor value
extsensor {port_num} {sen_type} label set "{name}"	sets sensor name to label
extsensor {port_num} {sen_type} label show	shows label of sensor
extsensor {port_num} type show	shows type of sensor
extsensor {port_num} {sen_type} {sen_field} events set {off=0|on=1}	enables sensor events on/off
extsensor {port_num} {sen_type} {sen_field} events show	shows if sensor events are enabled
extsensor {port_num} {sen_type} {sen_field} events type set "{EVT_SYSLOG=0,EVT_SNMP=1,EVT_EMAIL=2 ,EVT_SMS=3,EVT_GSMEMAIL=4,EVT_BEEPER =5,EVT_DISPLAY=6,EVT_CONSOLE=7,EVT_M QTT=8}"	enables different event types
extsensor {port_num} {sen_type} {sen_field} events type show	shows what event types are enabled
extsensor {port_num} {sen_type} {sen_field} events beeper mode set {CONTINOUS=0| INTERMITTENT=1}	sets beeper tone
extsensor {port_num} {sen_type} {sen_field} events beeper mode show	shows beeper tone
extsensor {port_num} {sen_type} {sen_field} maxval set {num}	sets maximum value for sensor
extsensor {port_num} {sen_type} {sen_field} maxval show	shows maximum value for sensor
extsensor {port_num} {sen_type} {sen_field} minval set {num}	sets minimum value for sensor
extsensor {port_num} {sen_type} {sen_field} minval show	shows minimum value for sensor
extsensor {port_num} {sen_type} {sen_field} hyst set {num}	sets hysterese value for sensor
extsensor {port_num} {sen_type} {sen_field} hyst show	shows hysterese value for sensor
extsensor {port_num} {sen_type} {sen_field} publish mode set {NONE=0|INTERVAL=1| DELTA=2|INTERV_DELTA=3}	sets publish mode
extsensor {port_num} {sen_type} {sen_field} publish mode show	shows publish mode
extsensor {port_num} {sen_type} {sen_field} publish mqtt retain set {OFF=0|ON=1}	sets mqtt retain
extsensor {port_num} {sen_type} {sen_field} publish mqtt retain show	shows if mqtt retain set
extsensor {port_num} {sen_type} {sen_field} publish timer set {num_secs}	sets publish time interval
extsensor {port_num} {sen_type} {sen_field} publish timer show	shows publish time interval
extsensor {port_num} {sen_type} {sen_field} publish delta set {float}	sets publish delta value
extsensor {port_num} {sen_type} {sen_field} publish delta show	shows publish delta value
extsensor {port_num} {sen_type} {sen_field} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2| BELOWMAX=3} port set {port_num}	sets Port for Power Port Switching actions
extsensor {port_num} {sen_type} {sen_field} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2| BELOWMAX=3} port show	shows Port for Power Port Switching actions
extsensor {port_num} {sen_type} {sen_field} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2| BELOWMAX=3} state set {OFF=0|ON=1| DISABLED=2}	sets Port state for Power Port Switching actions
extsensor {port_num} {sen_type} {sen_field} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2| BELOWMAX=3} state show	shows Port state for Power Port Switching actions
extsensor period set {24H=0|12H=1|2H=2|1H=3|30MIN=4}	sets sensor Min/Max measurement period
extsensor period show	shows sensor Min/Max measurement period
extsensor beeper set {OFF=0|ON=1}	enables beeper sensor alarms
extsensor beeper show	shows if beeper sensor alarms are enabled
extsensor {port_num} {sen_field} calib set {float}	sets calibration offset for temperature or humidity
extsensor {port_num} {sen_field} calib show	shows calibration offset for temperature or humidity
http	enters cmd group "http"
http server set {HTTP_BOTH=0|HTTPS_ONLY=1|HTTP_ONLY=22|HTTPS_REDIR=3}	sets accepted connection types
http server show	shows accepted connection types
http port set {ip_port}	sets http port
http port show	shows http port
http portssl set {ip_port}	sets https port
http portssl show	shows https port
http tls mode set {TLS12=0|TLS13_12=1|TLS13=2|TLS13_12_11=3}	restricts TLS mode
http tls mode show	shows TLS mode restriction
http auth mode set {BASIC=0|SESSION=1|SESSION_EXT=2}	sets http session authentication mode
http auth mode show	shows http session authentication mode and compatibility
http passwd enabled set {OFF=0|ON=1}	enables http password on/off
http timeout admin set {num_secs}	sets admin session timeout
http timeout admin show	shows admin session timeout
http timeout user set {num_secs}	sets user session timeout
http timeout user show	shows user session timeout
http passwd enabled show	shows if http password enabled
http passwd local set {OFF=0|ON=1}	enables local login on/off
http passwd local show	shows if local login enabled
http passwd radius set {OFF=0|ON=1}	enables login for RADIUS on/off
http passwd radius show	shows if RADIUS login enabled
http passwd user set "{passwd}"	sets http user password
http passwd admin set "{passwd}"	sets http admin password
http passwd hash user set "{passwd}"	sets hashed http user password http passwd hash admin set "{passwd}" sets hashed http admin password
ip4	enters cmd group "ip4"
ip4 hostname set "{name}"	sets device hostname
ip4 hostname show	shows device hostname
ip4 address set "{ip_address}"	sets IPv4 address
ip4 address show	shows IPv4 address
ip4 netmask set "{ip_address}"	sets IPv4 netmask
ip4 netmask show	shows IPv4 netmask
ip4 gateway set "{ip_address}"	sets IPv4 gateway address
ip4 gateway show	shows IPv4 gateway address
ip4 dns set "{ip_address}"	sets IPv4 DNS server address
ip4 dns show	shows IPv4 DNS server address
ip4 dhcp enabled set {OFF=0|ON=1}	enables IPv4 DHCP on/off
ip4 dhcp enabled show	shows IPv4 DHCP state
ip6	enters cmd group "ip6"
ip6 enabled set {OFF=0|ON=1}	enables IPv6 on/off
ip6 enabled show	shows if IPv6 is enabled
ip6 routadv enabled set {OFF=0|ON=1}	enables IPv6 router advertisement
ip6 routadv enabled show	shows IPv6 router advertisement state
ip6 dhcp enabled set {OFF=0|ON=1}	enables IPv6 DHCP on/off
ip6 dhcp enabled show	shows if IPv6 DHCP is enabled
ip6 address show	show all IPv6 addresses
ip6 gateway show	show all IPv6 gateways
ip6 dns show	show all IPv6 DNS server
ip6 manual enabled set {OFF=0|ON=1}	enables manual IPv6 addresses
ip6 manual enabled show	shows if manual IPv6 addresses are enabled
ip6 manual address {1..4} set "{ip_address}"	sets manual IPv6 address
ip6 manual address {1..4} show	shows manual IPv6 address
ip6 manual gateway set "{ip_address}"	sets manual IPv6 gateway address
ip6 manual gateway show	shows manual IPv6 gateway address
ip6 manual dns {1..2} set "{ip_address}"	sets manual IPv6 DNS server address
ip6 manual dns {1..2} show	shows manual IPv6 DNS server address
ipacl	enters cmd group "ipacl"
ipacl ping enabled set {OFF=0|ON=1}	enables ICMP ping on/off
ipacl ping enabled show	shows if ICMP ping enabled
ipacl enabled set {OFF=0|ON=1}	enable IP filter on/off
ipacl enabled show	shows if IP filter enabled
ipacl filter {ipacl_num} set "{dns_name}"	sets IP filter {ipacl_num}
ipacl filter {ipacl_num} show	shows IP filter {ipacl_num}
linesensor	enters cmd group "linesensor"
linesensor all {field_list} show	shows energy sensors according field list of all line sensors
linesensor {line_num} {field_list} show	shows energy sensors according field list of one line sensor
linesensor {line_num} {energy_sensor} value show	shows energy sensor of given line
linesensor {line_num} ovp show	show state of Overvoltage Protection
linesensor {line_num} counter reset	resets energy metering counter
linesensor {line_num} label set "{name}"	sets line meter to label
linesensor {line_num} label show	shows label of line meter
linesensor {line_num} {energy_sensor} events set {OFF=0|ON=1}	enables events on/off
linesensor {line_num} {energy_sensor} events show	shows if events are enabled
linesensor {line_num} {energy_sensor} events type set "{EVT_SYSLOG=0,EVT_SNMP=1,EVT_EMAIL=2,EVT_SMS=3,EVT_GSMEMAIL=4,EVT_BEEPER =5}"	enables different event types
linesensor {line_num} {energy_sensor} events type show	shows what event types are enabled
linesensor {line_num} {energy_sensor} events beeper mode set {CONTINOUS=0| INTERMITTENT=1}	sets beeper tone
linesensor {line_num} {energy_sensor} events beeper mode show	shows beeper tone
linesensor {line_num} {energy_sensor} maxval set {float}	sets maximum value for line meter
linesensor {line_num} {energy_sensor} maxval show	shows maximum value for line meter
linesensor {line_num} {energy_sensor} minval set {float}	sets minimum value for line meter
linesensor {line_num} {energy_sensor} minval show	shows minimum value for line meter
linesensor {line_num} {energy_sensor} hyst set {float}	sets hysterese value for line meter
linesensor {line_num} {energy_sensor} hyst show	shows hysterese value for line meter
linesensor {line_num} {energy_sensor} publish mode set {NONE=0|INTERVAL=1|DELTA=2| INTERV_DELTA=3}	sets publish mode
linesensor {line_num} {energy_sensor} publish mode show	shows publish mode
linesensor {line_num} {energy_sensor} publish mqtt retain set {OFF=0|ON=1}	sets mqtt retain
linesensor {line_num} {energy_sensor} publish mqtt retain show	shows if mqtt retain set
linesensor {line_num} {energy_sensor} publish timer set {num_secs}	sets publish time interval
linesensor {line_num} {energy_sensor} publish timer show	shows publish time interval
linesensor {line_num} {energy_sensor} publish delta set {float}	sets publish delta value
linesensor {line_num} {energy_sensor} publish delta show	shows publish delta value
linesensor {line_num} {energy_sensor} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2| BELOWMAX=3} port set {port_num}	sets Port for Power Port Switching actions
linesensor {line_num} {energy_sensor} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2| BELOWMAX=3} port show	shows Port for Power Port Switching actions
linesensor {line_num} {energy_sensor} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2| BELOWMAX=3} state set {OFF=0|ON=1| DISABLED=2}	sets Port state for Power Port Switching actions
linesensor {line_num} {energy_sensor} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2| BELOWMAX=3} state show	shows Port state for Power Port Switching actions
linesensor {line_num} events set {OFF=0|ON=1}	LEGACY - enables events on/off
linesensor {line_num} events show	LEGACY - shows if events are enabled
linesensor {line_num} events type set "{EVT_SYSLOG=0,EVT_SNMP=1,EVT_EMAIL=2 ,EVT_SMS=3,EVT_GSMEMAIL=4,EVT_BEEPER=5,EVT_DISPLAY=6,EVT_CONSOLE=7,EVT_M QTT=8}"	LEGACY - enables different event types
linesensor {line_num} events type show	LEGACY - shows what event types are enabled
linesensor {line_num} maxval set {float}	LEGACY - sets maximum value for line meter
linesensor {line_num} maxval show	LEGACY - shows maximum value for line meter
linesensor {line_num} minval set {float}	LEGACY - sets minimum value for line meter
linesensor {line_num} minval show	LEGACY - shows minimum value for line meter
linesensor {line_num} hyst set {float}	LEGACY - sets hysterese value for line meter
linesensor {line_num} hyst show	LEGACY - shows hysterese value for line meter
linesensor {line_num} {BELOWMIN=0| ABOVEMIN=1|ABOVEMAX=2|BELOWMAX=3} port set {port_num}	LEGACY - sets Port for Power Port Switching actions
linesensor {line_num} {BELOWMIN=0| ABOVEMIN=1|ABOVEMAX=2|BELOWMAX=3} port show	LEGACY - shows Port for Power Port Switching actions
linesensor {line_num} {BELOWMIN=0|ABOVEMIN=1|ABOVEMAX=2|BELOWMAX=3} state set {OFF=0|ON=1|DISABLED=2}	LEGACY - sets Port state for Power Port Switching actions
linesensor {line_num} {BELOWMIN=0| ABOVEMIN=1|ABOVEMAX=2|BELOWMAX=3} state show	LEGACY - shows Port state for Power Port Switching actions
linesensor beeper set {OFF=0|ON=1}	enables beeper for line meter alarms
linesensor beeper show	shows if beeper for line meter alarms is enabled
modbus	enters cmd group "modbus"
modbus enabled set <off=0/on=1>	enables Modbus TCP support
modbus enabled show	shows if Modbus is enabled
modbus port set <ip_port>	sets Modbus TCP port
modbus port show	shows Modbus TCP port
mqtt	enters cmd group "mqtt"
mqtt {broker_idx} enabled set {OFF=0|ON=1}	enable mqtt
mqtt {broker_idx} enabled show	shows if mqtt enabled
mqtt {broker_idx} server set "{dns_name}"	sets broker name
mqtt {broker_idx} server show	shows broker name
mqtt {broker_idx} tls enabled set {OFF=0|ON=1}	enable TLS
mqtt {broker_idx} tls enabled show	shows if TLS enabled
mqtt {broker_idx} port set {ip_port}	set broker TCP/IP port
mqtt {broker_idx} port show	shows broker TCP/IP port
mqtt {broker_idx} user set "{username}"	sets username
mqtt {broker_idx} user show	shows username
mqtt {broker_idx} passwd set "{passwd}"	sets password
mqtt {broker_idx} passwd hash set "{passwd}"	sets hashed passwd
mqtt {broker_idx} client set "{name}"	sets client name
mqtt {broker_idx} client show	shows client name
mqtt {broker_idx} qos set {QOS0=0|QOS1=1}	sets QoS level
mqtt {broker_idx} qos show	shows QoS level
mqtt {broker_idx} keepalive set {num_secs}	sets keep-alive time
mqtt {broker_idx} keepalive show	shows keep-alive time
mqtt {broker_idx} topic set "{name}"	sets topic prefix
mqtt {broker_idx} topic show	shwos topic prefix
mqtt {broker_idx} console enabled set {OFF=0| ON=1}	permit console cmds
mqtt {broker_idx} console enabled show	shows if console cmds allowed
mqtt {broker_idx} device data timer set {num_secs}	sets telemetry interval
mqtt {broker_idx} device data timer show	shows telemetry interval
port	enters cmd group "port"
port {port_num} state set {OFF=0|ON=1}	sets port to new state
port {port_num} state show	shows port state
port all state set "{port_list}" {OFF=0|ON=1}	sets several ports in one cmd - e.g. port all state set "1,3,5" 1
port all state {MODE0=0|MODE1=1|MODE2=2} show	shows all port states in 3 different view modes
port all set {OFF=0|ON=1|OFF_REV=2|ON_REV=3}	switch all ports on/off forward or reverse
port restart all set {REINIT=0| OFF_REV_REINIT=1,OFF_REINIT=2}	reinit coldstart sequence (optional first all off)
port {port_num} reset	start reset sequence for port
port {port_num} toggle	toggles port
port {port_num} batch set {OFF=0|ON=1} wait {num_secs} {OFF=0|ON=1}	starts batch mode for port
port {port_num} batch cancel	cancels batch mode
port {port_num} label set "{name}"	sets port label name
port {port_num} label show	shows port label name
port {port_num} initstate coldstart set {OFF=0| ON=1|REMEMBER=2}	sets port coldstart initialization
port {port_num} initstate coldstart show	shows port coldstart initialization
port {port_num} initstate delay set {num}	sets port init delay
port {port_num} initstate delay show	shows port init delay
port {port_num} repowerdelay set {num}	sets port repower delay
port {port_num} repowerdelay show	shows port repower delay
port {port_num} resettime set {num}	sets port reset duration
port {port_num} resettime show	shows port reset duration
port {port_num} watchdog enabled set {OFF=0| ON=1}	sets port watchdog to on/off
port {port_num} watchdog enabled show	shows port watchdog state
port {port_num} watchdog mode set {OFF=0| PORT_RESET=1|IP_MS=2|IP_MS_INV=3}	sets port watchdog mode
port {port_num} watchdog mode show	shows port watchdog mode
port {port_num} watchdog type set {WD_ICMP=0| WD_TCP=1}	sets port watchdog type
port {port_num} watchdog type show	shows port watchdog type
port {port_num} watchdog link down set {OFF=0| ON=1}	sets if watchdog active when eth link down
port {port_num} watchdog link down show	shows if watchdog active when eth link down
port {port_num} watchdog host set "{dns_name}"	sets port watchdog host target
port {port_num} watchdog host show	shows port watchdog host target
port {port_num} watchdog port set {ip_port}	sets port watchdog TCP port
port {port_num} watchdog port show	shows port watchdog TCP port
port {port_num} watchdog pinginterval set {num}	sets port watchdog ping interval
port {port_num} watchdog pinginterval show	shows port watchdog ping interval
port {port_num} watchdog pingretries set {num}	sets port watchdog ping retries
port {port_num} watchdog pingretries show	shows port watchdog ping retries
port {port_num} watchdog retrybooting set {OFF=0|ON=1}	sets port watchdog retry booting to on/off
port {port_num} watchdog retrybooting show	shows port watchdog retry booting state
port {port_num} watchdog bootretries set {num}	sets port watchdog retry boot timeout
port {port_num} watchdog bootretries show	hows port watchdog retry boot timeout
radius	enters cmd group "radius"
radius {PRIMARY=0|SECONDARY=1} enabled set <off=0/on=1>	enables radius client
radius {PRIMARY=0|SECONDARY=1} enabled show	show if radius client enabled
radius {PRIMARY=0|SECONDARY=1} server set "<dns_name>"	sets radius server address
radius {PRIMARY=0|SECONDARY=1} server show	shows radius server address
radius {PRIMARY=0|SECONDARY=1} password set "{passwd}"	sets radius server shared secret
radius {PRIMARY=0|SECONDARY=1} password hash set "{passwd}"	sets radius server crypted shared secret
radius {PRIMARY=0|SECONDARY=1} auth timeout set {num_secs}	sets server request timeout
radius {PRIMARY=0|SECONDARY=1} auth timeout show	shows server request timeout
radius {PRIMARY=0|SECONDARY=1} retries set {0..99}	sets server number of retries
radius {PRIMARY=0|SECONDARY=1} retries show	shows server number of retries
radius chap enabled set <off=0/on=1>	enables CHAP
radius chap enabled show	shows if CHAP is enabled
radius message auth set <off=0/on=1>	enables request message authentication
radius message auth show	shows if request message authentication is enabled
radius default timeout set {num_secs}	sets default session timeout (when not returned as Session-Timout Attribute)
radius default timeout show	shows default session timeout
rcmb	enters cmd group "rcmb"
rcmb {mod_num} state show	show rcmb module state
rcmb {mod_num} {RMS=0|DC=1} value show	shows RMS/DC RC values
rcmb {mod_num} {RMS=0|DC=1} output show	shows module RMS/DC outputs
rcmb {mod_num} {RMS=0|DC=1} events set {OFF=0|ON=1}	enables sensor events on/off
rcmb {mod_num} {RMS=0|DC=1} events show	shows if sensor events are enabled
rcmb {mod_num} {RMS=0|DC=1} events type set "{EVT_SYSLOG=0,EVT_SNMP=1,EVT_EMAIL=2,EVT_BEEPER=5,EVT_DISPLAY=6,EVT_CONS OLE=7,EVT_MQTT=8}"	enables different event types
rcmb {mod_num} {RMS=0|DC=1} events type show	shows what event types are enabled
rcmb {mod_num} {RMS=0|DC=1} events beeper mode set {CONTINOUS=0|INTERMITTENT=1}	sets beeper tone
rcmb {mod_num} {RMS=0|DC=1} events beeper mode show	shows beeper tone
rcmb {mod_num} {RMS=0|DC=1} maxval set {float}	sets maximum value for sensor
rcmb {mod_num} {RMS=0|DC=1} maxval show	shows maximum value for sensor
rcmb {mod_num} {RMS=0|DC=1} minval set {float}	sets minimum value for sensor
rcmb {mod_num} {RMS=0|DC=1} minval show	shows minimum value for sensor
rcmb {mod_num} {RMS=0|DC=1} hyst set {float}	sets hysterese value for sensor
rcmb {mod_num} {RMS=0|DC=1} hyst show	shows hysterese value for sensor
rcmb {mod_num} {RMS=0|DC=1} publish mode set {NONE=0|INTERVAL=1|DELTA=2| INTERV_DELTA=3}	sets publish mode
rcmb {mod_num} {RMS=0|DC=1} publish mode show	shows publish mode
rcmb {mod_num} {RMS=0|DC=1} publish mqtt retain set {OFF=0|ON=1}	sets mqtt retain
rcmb {mod_num} {RMS=0|DC=1} publish mqtt retain show	shows if mqtt retain set
rcmb {mod_num} {RMS=0|DC=1} publish timer set {num_secs}	sets publish time interval
rcmb {mod_num} {RMS=0|DC=1} publish timer show	shows publish time interval
rcmb {mod_num} {RMS=0|DC=1} publish delta set {float}	sets publish delta value
rcmb {mod_num} {RMS=0|DC=1} publish delta show	shows publish delta value
rcmb {mod_num} {RMS=0|DC=1} {BELOWMIN=0| ABOVEMIN=1|ABOVEMAX=2|BELOWMAX=3} port set {port_num}	sets power port for sensor values action
rcmb {mod_num} {RMS=0|DC=1} {BELOWMIN=0| ABOVEMIN=1|ABOVEMAX=2|BELOWMAX=3} port show	shows power port for sensor values action
rcmb {mod_num} {RMS=0|DC=1} {BELOWMIN=0| ABOVEMIN=1|ABOVEMAX=2|BELOWMAX=3} state set {OFF=0|ON=1|DISABLED=2}	sets state for sensor values action
rcmb {mod_num} {RMS=0|DC=1} {BELOWMIN=0| ABOVEMIN=1|ABOVEMAX=2|BELOWMAX=3} state show	shows state for sensor values action
snmp	enters cmd group "snmp"
snmp port set {ip_port}	sets SNMP UDP port
snmp port show	shows SNMP UDP port
snmp snmpget enabled set {OFF=0|ON=1}	enables SNMP GET cmds on/off
snmp snmpget enabled show	show if SNMP GET cmds are enabled
snmp snmpset enabled set {OFF=0|ON=1}	enables SNMP SET cmds on/off
snmp snmpset enabled show	show if SNMP SET cmds are enabled
snmp snmpv2 enabled set {OFF=0|ON=1}	enables SNMP v2 on/off
snmp snmpv2 enabled show	show if SNMP v2 is enabled
snmp snmpv2 public set "{text}"	enables SNMP v3 on/off
snmp snmpv2 public show	show if SNMP v3 isenabled
snmp snmpv2 private set "{text}"	sets SNMP v2 public cummnity
snmp snmpv2 private show	shows SNMP v2 public community
snmp system {CONTACT=0|NAME=1| LOCATION=2} set "{text}"	sets sysLocation/sysName/sysContact
snmp system {CONTACT=0|NAME=1|LOCATION=2} show	gets sysLocation/sysName/sysContact
snmp snmpv3 enabled set {OFF=0|ON=1}	sets SNMP v2 private community
snmp snmpv3 enabled show	shows SNMP v2 private community
snmp snmpv3 username set "{text}"	sets SNMP v3 username
snmp snmpv3 username show	shows SNMP v3 username
snmp snmpv3 authalg set {NONE=0|MD5=1| SHA1=2|SHA256=3|SHA384=4|SHA512=5}	sets SNMP v3 authentication
snmp snmpv3 authalg show	show SNMP v3 authentication algorithm
snmp snmpv3 privalg set {NONE=0|DES=1| 3DES=2|AES128=3|AES192=4|AES256=5| AES192*=6|AES256*=7}	sets SNMP v3 privacy algorithm
snmp snmpv3 privalg show	show SNMP v3 privacy algorithm
snmp snmpv3 authpasswd set "{passwd}"	sets SNMP v3 authentication password
snmp snmpv3 privpasswd set "{passwd}"	sets SNMP v3 privacy password
snmp snmpv3 authpasswd hash set "{passwd}"	sets SNMP v3 authentication hashed password
snmp snmpv3 privpasswd hash set "{passwd}"	sets SNMP v3 privacy hashed password
snmp trap type set {NONE=0|V1=1|V2=2|V3=3}	sets type of SNMP traps
snmp trap type show	show SNMP trap type
snmp trap receiver {trap_num} set "{dns_name}"	sets address and port of SNMP trap receiver {trap_num}
snmp trap receiver {trap_num} show	show address and port of SNMP trap receiver {trap_num}
syslog	enters cmd group "syslog"
syslog enabled set {OFF=0|ON=1}	enables syslog msgs on/off
syslog enabled show	show if syslog enabled
syslog server set "{dns_name}"	sets address of syslog server
syslog server show	shows address of syslog server
system	enters cmd group "system"
system beeper manual set {OFF=0|ON=1} {millisec}	manually sets beeper with optional duration
system beeper manual show	shows beeper state
system restart	restarts device
system fabsettings	restore fab settings and restart device
system bootloader	enters bootloader mode
system flushdns	flush DNS cache
system uptime	number of seconds the device is running
system name show	shows device name
system version show	shows actual firmware version
system display {disp_num} default extsensor {port_num} {sen_type} set {sen_field}	shows external sensor
system display {disp_num} default linesensor {line_num} set {sen_field}	shows energy line sensor
system display {disp_num} default set {BLANK=0,LOCAL_TIME=1,UTC_TIME=2}	shows other contents
system display {disp_num} default show	shows default setting for display
system display default hash set "{data}"	sets hashed display setting
system display default hash show	shows hashed display setting
system sensor {VSYS=0|VAUX=1|VMAIN=2| TCPU=3} show	shows internal sensors if model supports it
system {SWITCH_PORT=0} events set {OFF=0| ON=1}	enable global events
system {SWITCH_PORT=0} events show	shows if global events enabled
system {SWITCH_PORT=0} events type set "{EVT_SYSLOG=0,EVT_SNMP=1,EVT_EMAIL=2,EVT_SMS=3,EVT_GSMEMAIL=4,EVT_BEEPER =5,EVT_DISPLAY=6,EVT_CONSOLE=7,EVT_MQTT=8}"	enables different event types
system {SWITCH_PORT=0} events type show	shows what event types are enabled
system {SWITCH_PORT=0} events mqtt retain set {OFF=0|ON=1}	sets mqtt retain
system {SWITCH_PORT=0} events mqtt retain show	shows if mqtt retain set
system panel enabled set {OFF=0|ON=1}	blocks panel buttons when not enabled
system panel enabled show	shows if panel buttons are enabled
system panel port all set {OFF=0|ON=1}	enable siwtch all relays from panel buttons
system panel port all show	shows if siwtch all relays from panel buttons enabled
timer	enters cmd group "timer"
timer enabled set {OFF=0|ON=1}	enables timer functions
timer enabled show	shows if timer a enabled
timer syslog facility set {0..23}	sets facility level for timer syslog
timer syslog facility show	shows facility level for timer syslog
timer syslog verbose set {0..7}	sets verbose level for timer syslog
timer syslog verbose show	shows verbose level for timer syslog
timer {rule_num} enabled set {OFF=0|ON=1}	enables rule
timer {rule_num} enabled show	shows if rule is enabled
timer {rule_num} name set "{name}"	sets name of rule
timer {rule_num} name show	shows name of rule
timer {rule_num} {FROM=0|UNTIL=1} set "{yyyymm-dd}"	sets date range of rule
timer {rule_num} {FROM=0|UNTIL=1} show	shows date range of rule
timer {rule_num} trigger jitter set {0..65535}	sets jitter for rule
timer {rule_num} trigger jitter show	show jitter of rule
timer {rule_num} trigger random set {0..100}	sets probability for rule
timer {rule_num} trigger random show	shows rule probability
timer {rule_num} trigger {HOUR=0|MIN=1|SEC=2| DAY=3|MON=4|DOW=5} set "{time_date_list}"	sets time date list
timer {rule_num} trigger {HOUR=0|MIN=1|SEC=2| DAY=3|MON=4|DOW=5} show	shows time date list
timer {rule_num} action mode set {SWITCH=1| CLI=2}	sets switch or cli cmd
timer {rule_num} action mode show	shows if switch or cli cmd
timer {rule_num} action {SWITCH1=0| SWITCH2=1} {OFF=0|ON=1} set "{port_list}"	sets port list for switch cmd
timer {rule_num} action {SWITCH1=0| SWITCH2=1} {OFF=0|ON=1} show	shows port list for switch cmd
timer {rule_num} action delay set {0..65535}	delay between cmds
timer {rule_num} action delay show	shows delay between cmds
timer {rule_num} action console set "{cmd}"	sets cmd string
timer {rule_num} action console show	shows cmd string
timer {rule_num} action hash set "{data}"	sets action binary form
timer {rule_num} action hash show	shows action binary form
timer {rule_num} delete	delete one timer
timer delete all	delete all timer
vt100	enters cmd group "vt100"
vt100 echo set {OFF=0|ON=1}	sets console echo state
vt100 echo show	shows console echo state
vt100 numeric set {OFF=0|ON=1}	sets numeric mode
vt100 numeric show	shows numeric mode state
vt100 reset	resets terminal